自動涼茬機是將攤晾、加漿、加曲、攪拌、卸料等工序一次性完成，與傳統工藝相比，大大降低勞動強度，實現機械自動化。如何穩定使用呢？下面小編為您講講。
The automatic stubble cooling machine completes the processes of spreading, adding pulp, adding koji, stirring, and unloading in one go. Compared with traditional processes, it greatly reduces labor intensity and achieves mechanical automation. How to use it stably? Below, the editor will explain to you.
一、安裝前應查看自動涼茬機各部位，零件是否有松動現象，如發現，需修理后方可安裝。
1、 Before installation, it is necessary to first check all parts of the automatic stubble cooling machine for any looseness. If any looseness is found, it needs to be repaired before installation.
二、安裝時，打茬機跑車輪與道軌間隙以打茬機與軌跡來回跑動時為規范。
2、 When installing, the gap between the stubble machine's running wheel and the track is standardized when the stubble machine runs back and forth with the track.
三、打茬機安裝結束后，需要行試工作五分鐘左右，查看各部位是否有雜音現象出現，如發現雜音應泊車檢修，待試工作正常后，方可投入正常生產運用。
3、 After the installation of the stubble cutting machine is completed, it is necessary to conduct a trial operation for about five minutes to check for any noise in various parts. If any noise is found, it should be parked for maintenance. After the trial operation is normal, it can be put into normal production and use.
四、運用過程中，應經常留意有無異常動靜，轟動是否加大，如發現雜音應及時泊車檢修。
4、 During the use process, it is necessary to regularly pay attention to any abnormal movements and increase the noise. If any noise is found, it should be promptly parked for maintenance.
五、打茬機投入運用后，應定期查看螺栓有無松動，零部件有無損壞，如發現應根據具體情況檢修或更換零部件。
5、 After the stubble cutting machine is put into use, it should be regularly checked for looseness of bolts and damage to components. If found, it should be repaired or replaced according to the specific situation.
六、在運用過程中，注油部位應定期注油，一般每三個月注黃油一次，以確保打茬機各傳動部位潤滑正常，減少磨損。
6、 During operation, the oil injection area should be regularly lubricated, usually with butter every three months, to ensure normal lubrication of all transmission parts of the stubble machine and reduce wear.
七、自動涼茬機若長時間停用從頭投入生產運用時，要從頭進行查看，并通過試車工作正常后再投入生產運用。
7、 If the automatic stubble cooling machine is stopped for a long time and put into production again, it should be checked from the beginning and put into production again after the test run is normal.
裝有多個軸流風機，通過風量的調節，使高溫涼茬在輸送過程中降到規定的溫度，攤晾效果好，在攤晾過程中設置多個攪拌裝置，使涼茬在攤晾過程中松散、不易結坨，加漿、下曲均勻，數量可調節，通過裝置可將漿水、曲粉、糧茬攪拌均勻。您有需求就來我們網站
http://m.justeve.cn咨詢！
Equipped with multiple axial flow fans, the air volume is adjusted to lower the high-temperature cool stubble to the specified temperature during transportation, resulting in good spreading effect. During the spreading process, multiple mixing devices are set up to make the cool stubble loose and not easy to clump. The addition of slurry and downward bending are uniform, and the quantity can be adjusted. Through the device, the slurry, koji powder, and grain stubble can be evenly mixed. Come to our website if you have any needs http://m.justeve.cn consulting service
自動售酒機 2024-07-25 
